Nu har jeg lige lavet en lyn-guide. Når jeg får mere tid, vil jeg lave en mere udførlig guide, med screen shots.
Her er hvordan man kommer i gang, helt fra punkt 0, med styringer fra Technische Alternative (
www.ta.co.at )
1) Anskaf en
CMI og
mindst et styremodul, f.eks. UVR16x2, RSM610, UVR1611 … dertil sensorer (typisk et bundt med PT1000 temperaturefølere), kabler mm, efter behov.
1A) “Bootloader" (BL-NET) kan bruges i stedet for CMI, men CMI er både nemmere at bruge, og kan flere ting. Der behøves kun 1x CMI til et helt system med mange moduler (med mindre det er et helt ekstremt stort system!)
2)
Opret en bruger på cmi.ta.co.at (CMI kører via en server i Østrig, og det er der man logger ind)
3)
Download programmer (især TAPPS2 og TA Designer), firmware (check serienummer på f.eks. ældre UVR1611) og manualer på
https://www.ta.co.at/en/downloads.
4) Sørg for at ha adgang til en
Windows computer, alternativt LINUX, eller en MAC med f.eks. Parallels til at køre Windows. Windows XP (64bit) eller nyere kan bruges, så har man ikke en Windows computer kan man sikkert købe en ældre model billigt.
5) Sørg for der er
internet til CMI - et
ethernet kabel til en
router eller switch der har internet adgang, eller anden forbindelse (med kabel). Hvis der kun er WiFi til rådighed, skal man ha en boks der laver wifi til ethermet.
6) Forbind CMI til ethernet, og CAN bus til styre-enhed(er). Sæt
terminering i begge ender af CAN bussen (en "lus", se manualen). Sæt strøm til apparaterne. Bemærk at der er DC på can bussen, så CMI kan f.eks. få strøm via UVR1611 / UVR16x2 / RSM610. Det er dog bedst at hvert apparat har sin egen forsyning. CMI skal ha 4 grønne LED, ellers er der noget der ikke er sat korrekt op. Nogle apparater skal ha 230V AC, for at kunne virke, f.eks. UVR1611, UVR16x2.
7) Log ind på cmi.ta.co.at og
tilføj CMI (se
serienummer og kode på CMI boksen)
8 ) Opdater
firmware i CMI og styre-enheder som nødvendigt (for ældre apparater, check serienummer for at se hvilken firmware der kan benyttes - gælder især ældre UVR1611 modeller)
9) Åben
TAPPS2 og lav et simpelt “program”. Start med en simpel funktion, for at teste og komme i gang. Gem filen (
.dat format)
10) fra cmi.ta.co.at,
klik på nummeret med blå skrift på CMI, f.eks.
CMI0012345. Det åbner for adgang til CMI. Der skulle gerne komme et billede af en CMI, med 4 grønne LED. Klik på "CAN Bus" for at se de tilsluttede enheder, derefter klik på “Data Administration”
11) For at sende et program til en styreenhed, skal det
først sendes til CMI’en. Det gør man ved at trække .dat filen fra TAPPS2 over på hvor der står “Drag data here”. Der skal være et formateret SD kort i CMI, og der skal være nok plads på det
12) .dat Filen man lige har uploadet skulle gerne kunne
ses i højre side af "Data Administration". Man
trækker filen til venstre og slipper det oven i det apparat man vil sende til. Der går nu et par minutter med overførsel og genstart af styreenheden. Det er muligt der kommer et par
fejlmeddelser, mens der genstartes (tilsvarende hvis man genstarter en internet router). Bare gi den et par minutter for genstart. Sørg for at node nummer på enheden er det samme som det man har programmeret det til (se manualen for mere info)
13) Klik på
CAN Bus i menuen, for at se hvilke apparater der er online på CAN bussen. Klik på en af de viste apparater for at få
adgang direkte til det pågældende apparat.
14) Åben
TA Designer programmet. Åben et nyt diagram. Importer .dat filen fra TAPPS2. Nu kan man lave et
online skema aka
Diagram. Når det er gemt, overføres filen til samme sted som .dat filen - og så kan man se det online diagram ved at klikke på “Diagram” i menuen på cmi.ta.co.at
Bemærk, at styre-enhederne låses i forskellige tilstande, f.eks. "user" og "expert". For at uploade programmer og andre mere tekniske ting, skal man for hvert apparat først vælge "expert", og til dette angive en kode som man kan finde i manualerne et sted. Man kan selv ændre koden senere. Koden er altid et tal, der er hverken bogstaver eller tegn. Dette er udelukkende for at forhindre at en slutbruger ødelægger opsætningen, hvad enten det er med fortsæt eller pga manglende erfaring med systemet.
-
Jeg vil vende tilbage og opdatere den her post senere, eller poste en revideret version hvis jeg ikke længere kan/må rette i den her post.